国产SUV精品一区二区88,国产免费MV大全视频网站,日韩精品在线观看,久久精品丝袜高跟鞋

This pilling is a thermally conductive thermally conductive dielectric silicon material, or a quick fixation. Designed for an electronic electrical product having a very large amount of heat dissipation after potting rear protection, it consists of A and B two-component liquid. After sufficiently mixing at 1: 1 weight, the mixed liquid can be cured as an elastomer, and the material is not Obvious contraction and fever, the solidified colloid has excellent physical and electrical properties of silicone materials.

If you still have questions after you read it, please click the QR code to enter the high-conducting potty adhesive small video in the shake number, which can more intuitively see the whole picture of this product.
 

Performance characteristics

● High heat transfer, thermal conductivity is 1.5 w / m · k;

● Low viscosity, as low as 4600 mPa · s, good fluidity, good fill, and faster bubbles after pnery;

● Excellent flame retardation performance, reaching V0 level;

● Elastomer, good anti-shock impact and deformation ability;

● -50 ° C ~ 200 ° C can maintain stable physical mechanical properties for a long time,

● With blanking, the components after potting can be repaired and replaced;

● Curing, heating to 85 ° C, can be completely solidified, and improve work efficiency is improved.

Typical use typical application

For more power supplies, such as fast charge, large watts.

technical parameter

state status	Test items	unit	parameter parametric	Remark remark
Before curing	color		grey gray pessimistic	A component
			White white	B component
	Viscosity	25oC, MPA S	4500 ± 1000	A component
			4800 ± 1000	B component
	density	25oC，g/cm3	2.40 ± 0.2	A component
			2.40 ± 0.2	B component
	The mixing ratio		1: 1
	Operating time	25oC RH 50%, min
	Curing time	25oC RH 50%, HR
		85oC,Hr
After curing	color		grey gray pessimistic	After mixing
	hardness	Shore A	35 ± 5
	Thermal Conductivity	w/m·k
	Dielectric constant	1.2MHz	3.0 ~ 3.3
	Dielectric strength	Kv/mm(25oC)
	Volume resistance	(DC500V), O. CM	1.0 × 1014

Instructions

Mix

The product is provided in two-component form, producing a small amount of precipitation during transportation and storage, should be pre-stirred before use. After a component is thoroughly mixed with B components, gently agitate to reduce the amount of air mixed. Vacuum sputum treatment before perfusion can reach the most ideal rolled state.

 

2. Applicable period / operation time

The curing reaction starts at the beginning of the mixing process. The initial curing phenomenon is gradually increased, and then the gel is started, and then transformed into an elastomer. The definition of the applicable period is that the viscosity increases to the original twice as component A and B (mains and curing agents).

 

3. Processing and Curing

After the product is fully mixed, it can be directly injected / dispensing to a component that requires curing, and the components should be vacuum-deprived after using the product pot. The product can be cured either at room temperature (25 ° C) or heated.

 

4. Temperature range available

For most applications, the product can be used in a temperature range of -50 to 200 ° C.

 

5. Compatibility

In some cases, this product will not be able to achieve the most desirable curing effect when contacting some plastic or rubber, and the surface of the solvent is cleaned or baked with a slight baked above the curing temperature can be resolved.

Some chemicals can inhibit curing, and the following materials should pay special attention: an organic substance containing N, P, S, and an ionic compound containing Sn, Pb, Hg, Bi, AS or the like; compounds containin enhance the adhesion, combining the repaired materials with existing pottings.

 

7. Operational precautions

1.a, b Components must be stirred after 2-5 minutes after opening the original package, avoiding the effects of product effects due to the layered precipitation caused during transportation and storage.

2. When mixing, consolidate agitation, especially the stirring;

 

(5) Storage and validity period

When there is no open seal below 25 ° C, the product from the date of production is 6 months. If it is overdue, it can be used normally after test inspection.

 

(6) Packaging specifications:

25kg / barrel;